Page 1 of 12 12311 ... LastLast
Results 1 to 10 of 112

Thread: Installing Honda Wind Deflectors Set 08P70-MEW-100

  1. #1
    Moderator RedLdr1's Avatar
    Join Date
    Dec 2010
    Location
    Woodstock, Georgia
    Posts
    5,039
    My Gallery

    Installing Honda Wind Deflectors Set 08P70-MEW-100

    The instructions Honda provides are pretty good but I found a couple of tricks to make it easier.

    This is what the Wind Deflector kit contained:



    Here is how I installed them:

    1. Remove the mirrors. Note: You will need a Torx T-40 to remove the screws holding on the mirrors.

    2. Test fit the part and see how it fits on the bottom half against the fairing.

    3. Clean the areas where the 3M Tape will be sticking to the fairing.

    4. Remove the red tape backing on the bottom half of the unit and install it lightly. It is designed to fit snugly and is fairly easy to align. Don't press it down hard yet, just use enough pressure to get it to stay in place.

    5. Test fit the top and see how it fits on the fairing and most importantly how it aligns with the screw holes.

    6. Once it aligns remove the red tape backing from the top half of the unit. Install it making sure it aligns with the screw holes as well as aligning on the fairing. Once again don't press it down hard yet, just enough pressure to hold it in alignment.

    It should look like this:




    7. Next insert the supplied spacers in the "pocket" in the Wind Deflector above the mirror mounting screws.

    8. Install the mirror using the supplied 6MM Hex screws. Don't tighten them yet, just get everything lined up.

    9. Now if all the parts are in alignment press down the tape firmly on the top and bottom halves and tighten your mirrors down.



    Finished!


    › Site Search for: Installing Honda Wind Deflectors Set 08P70-MEW-100
    Wayne
    1987 Yamaha FJ1200
    AMA Life Member

  2. #2
    bassplayer's Avatar
    Join Date
    Dec 2010
    Location
    Seabrook, Texas, between Houston and Galveston.
    Posts
    114
    My Gallery
    Thanks to these instructions I was able to do my install on Saturday, very easy. I had to use th T-30 and my new nolts were 4 mm hex. The difference with the Torx size could have had something to do with my tring first with an alternate method, bad idea. the replacement bolts were 4 mm for sure, it could be they have changed a bit as I just got munie a couple of weeks ago.
    I rode to work this morning, temp around 38 F, ther was a difference. I had to move my hand off the bar to the side to feel the wind flow. They work, but better yet, I think they look good.

  3. #3
    Paul's Avatar
    Join Date
    Dec 2010
    Location
    Ocala, FL
    Posts
    799
    My Gallery
    Wayne,
    Thanks for reposting the instructions. I am still considering adding the wind deflectors.
    Paul

  4. #4
    bassplayer's Avatar
    Join Date
    Dec 2010
    Location
    Seabrook, Texas, between Houston and Galveston.
    Posts
    114
    My Gallery
    Paul, They are a bit overpriced for what they are, but they do work. I'm glad I went ahead and got them.
    Eric
    2010 NT700V abs
    2008 Sv 650N

  5. #5
    They actually keep my gloves dryer in the rain amazing how well they work. Lots of Aerodynamic homework to make that simple shape work so well.....

  6. #6
    Herb's Avatar
    Join Date
    Dec 2010
    Location
    Huntington NY
    Posts
    605
    My Gallery
    I used Wayne's pictures and instructions when I put mine on about a month ago. I ride year around. They work very well with heated grips to keep my hands comfortable. Yes, pricey, bot functional and wrath. I love the way they frame the turn signal lights at night.
    Herb
    Huntington, NY

  7. #7
    Mattdenn's Avatar
    Join Date
    Dec 2010
    Location
    Reading, PA
    Posts
    61
    My Gallery
    I'm glad I added mine this past summer. Made a world of difference on a 5 day trip down South with my brother. Lots of rain & cold temps. Worth the Farkle Dollars........MATT
    MSTA & AMA Member

  8. #8
    Silver NT ABS SN:0191 CoolNT's Avatar
    Join Date
    Dec 2010
    Location
    Houston, TX
    Posts
    432
    My Gallery
    Spraying some WD40 and letting it sit for a bit would have done it. If that wouldn't have, then a bit of light couple taps and turn.
    Ron
    Motorcycle enthusiast

  9. #9
    One thing I did to help locate were the top of the wing goes is to put one of the spacers on a screw and screw it in to the mirror mount. It give you a way to locate where the top of the wing goes before the tape touches.
    Walt

    It's more fun to ride a slow bike fast than it is to ride a fast bike slow.

  10. #10
    Desert Dan's Avatar
    Join Date
    Dec 2010
    Location
    Palm Desert California
    Posts
    341
    My Gallery
    Okay Wayne I followed directions and the install was easy. Not waiting 24 hours like they say to take a ride though, only about 18 hours. Hope they don't fall off. They do look cool.
    Dan
    Black 2014 Yamaha Bolt 950 "Raven"
    "keep the rubber side down, you'll live to smell the roses"


+ New Posts
Page 1 of 12 12311 ... LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •